ChemEng stuff followers

Showing posts with label densidad. Show all posts
Showing posts with label densidad. Show all posts

Saturday, June 13, 2026

Calculadora de la densidad del agua

Calculadora de la densidad del agua

La densidad del agua varía en función de la temperatura. Para obtener un cálculo preciso en un amplio rango, se utiliza la siguiente ecuación polinomial empírica:

\[\rho(T) = \frac{999.84 + 16.95 T - 7.99\times 10^{-3} T^2 - 46.17\times 10^{-6} T^3 + 105.56\times 10^{-9} T^4 - 280.54\times 10^{-12} T^5}{1 + 16.88\times 10^{-3} T}\]

Donde:

  • \(\rho\) es la densidad del agua en kg/m³.
  • \(T\) es la temperatura en °C.

Densidad Calculada:

--- kg/m³

Saturday, April 12, 2025

About slugs and pound units

 This post is intended to provide a common ground on the usage of these Imperial and US customary units.

The units $slugs$ and pound-mass ($lb_m$) are sometimes used as synonyms for mass units. However, only the $slug$ is a true unit of mass.

The $lb_m$ is something else. The equivalence between these two quantities is,

$1\, slug=1\, lb_f\cdot s^2/ ft= \dfrac{1\,lb_m}{32.17\,ft/s^2}$        Eq. (01)

where the unit $lb_f$, or pound-force, was introduced too. Many times, instead of writting $lb_f$, people just write $lb$. Also, $1.0\, lb_f$ has a mass of $1.0\, lb_m$ and the only way the above Eq. (01) really works is by introducing the constant $g_c$ as follows,

$g_c=\dfrac{32.17\, lb_m}{lb_f/\left( ft/s^2 \right)}=\dfrac{32.17\,lb_m\cdot ft/s^2}{lb_f}$        Eq. (02)

which is as you can see a adjusting parameter to fix the unit system.

One in which this $g_c$ occurs is in the well known formula,

$F=mg$        Eq. (03)

to calculate the force $F$ from the mass $m$ and the acceleration due to gravity $g$. Equation (03) works well in SI units but not if Imperial units are introduced. For these purposes, Eq. (03) must be changed to,

$F=m\dfrac{g}{g_c}$        Eq. (04)

Otherwise, physical inconsistencies would arise. However, another remedy is possible: make use of $slugs$ rather than $lb_m$, so that $g_c$ is no longer needed.

Working with Imperial units can be confusing but using the presented equivalencies you will succeed (hopefully).

Friday, April 11, 2025

The density of a mixture

- Two components of equal mass but different volume - 

Knowing the density of such a mixture is a common strange situation in engineering. This demonstration can be extended to more components provided the mass of each component is the same.

The situation

Consider that you have a solution, of a solid with certain density $\rho_S$ dilute in certain solvent of density $\rho_L$, in which both the solute and solvent are mixed in equal quantities. This is, the mass of the solute is equal to the mass of the solvent. What is the density of such a mixture?

An analytical approach

The solution to this case is not knew and can also be found elsewhere. However, in this post, some different flavor shall be given.

The density of the solute is,

$\rho_S=\dfrac{m_S}{V_S}$        Eq. (01)

while the density of the solvent is,

$\rho_L=\dfrac{m_L}{V_L}$        Eq. (02)

but since the mass of solute and solvent are equal, it follows,

$m=m_S=m_L$        Eq. (03)

Also, the density of the mixture should be,

$\rho=\dfrac{m_S+m_L}{V_S+V_L}=\dfrac{2m}{V_S+S_L}$       Eq. (04) 

The volumes, $V_S$ and $V_L$, in Eq .(04) can be determined from Eqs. (01-02) condering Eq. (03) as follows,

$V_S=\dfrac{m}{\rho_S}$        Eq. (05)

$V_L=\dfrac{m}{\rho_L}$        Eq. (06)

Substitution of Eqs. (05-06) into Eq. (04) produces,

$\rho=\dfrac{2m}{\dfrac{m}{\rho_S}+\dfrac{m}{\rho_L}}$

which can be simplified,

$\rho=\dfrac{2m}{\dfrac{\rho_L m+\rho_S m}{\rho_S \rho_L}}=\dfrac{2m}{\dfrac{m\left( \rho_L+\rho_S \right)}{\rho_S \rho_L}}=\dfrac{2\rho_S \rho_L}{\rho_L+\rho_S}$            Eq. (07)

Of course, Eq. (07) applies for the mixture of two liquids as well. Therefore, if you know the density of both substances, you can readily estimate the density of the mixture (provided the mass of the two components is the same).

A case to estimate the density of a mixture

Let us consider a slurry fluid made of the mixture of coal and water. The coal has specific gravity 2.5 while the slurry has composition 50% coal w/w. What is the density of the slurry?

Well, the slurry mixture is made of coal and water mixed in the same mass proportion. This is, the mass of the coal is the same as the mass of the water used to make the slurry. The volume is unknown: it can be the same but, who knows.

Starting with the specific gravity of the coal (solute), its density should be,

$\rho_S=\left(2.5\right) \left( 1000\,kg/m^3 \right)=2500\,kg/m^3$

For the water, let us consider that it is at room temperature (say, 25 °C). Similar temperatures around this one will give a very similar water density, so that you do not have to worry too much. Then,

$\rho_L=997.05\, kg/m^3$

Therefore, the density of such a slurry should be,

$\rho=1425.56\, kg/m3$

This is the end of the post. I hope you find it useful.

Ildebrando.


Saturday, April 5, 2025

Hydraulic equations for non newtonian fluids

 Here, the hydraulic equations for two known non-Newtonian fluids are presented. These are,

  • the power law fluid and
  • the Bingham plastic fluid.

These equations are to focus on the flow rate $Q$, the Reynolds number $N_{Re}$, and the friction factor $f_F$, for the case of a fluid flowing through a pipe of circular section.

A comment on the friction factors

There are, in fluid mechanics, two different friction factors:

  • the Darcy friction factor
  • the Fanning friction factor

This is confusing if you are not aware of this fact. The Darcy friction factor (say $f_F$) and the Fanning's (say $f_{FF}$) are related as follows,

$f_F=4\,f_{FF}$

You should pay attention when using Darcy's equation for head loss since it is originally and commonly expressed in terms of $f_F$. This means that if you are using $f_{F}$ the head loss can be found from:

$h_L=2f_{FF}\dfrac{L}{D}\dfrac{V^2}{g}$

In this post, the formulas for the newtonian fluid use the Darcy friction factor $f_F$ while those for power law and plastic Bingham fluids use the Fanning friction factor $f_{FF}$.

Newtonian fluid

The flow rate $Q$ is given by,

$Q=\dfrac{\pi\,R^4}{8\mu}\dfrac{P_0-P_L}{L}$        Eq. (01)

where $R$ is the pipe internal radius and subscripts $0$ and $L$ indicate the end and final of the pipe.

The Reynolds number $N_{Re}$ is given by,

$N_{Re}=\dfrac{D\,V}{\nu}$        Eq. (02)

The friction factor $f_F$,for laminar conditions $N_{Re}<2000$, is given by,

$f_{F-L}=\dfrac{64}{N_{Re}}$        Eq. (03)

for turbulent flow regime $N_{Re}>4000$ by,

$\dfrac{1}{\sqrt{f_{F-T}}}=-2\log_{[10]}\left( \dfrac{\epsilon}{3.72D}+\dfrac{2.51}{N_{Re}\sqrt{f_{F-T}}} \right)$        Eq. (04)

Power law fluid

The flow rate $Q$ is given by,

$Q=\dfrac{\pi\,R^3}{(1/n)+3}\left(\dfrac{\left(\mathbb{P}_0-\mathbb{P}_L\right)R}{2mL}\right)^{1/n}$        Eq. (05)

where $R$ is the pipe internal radius and subscripts $0$ and $L$ indicate the end and final of the pipe. The formula in Eq. (05) was taken from the familiar book Dynamics of Polymeric Liquids by Bird R. B. et al. Also, the velocity given as a function of the pipe radius is,

$v_z=\left( \dfrac{\tau_R}{m} \right)^{1/n}\dfrac{R}{(1/n)+1}\left[ 1-\left( \dfrac{r}{R} \right)^{(1/n)+1} \right]$        Eq. (05a)

where,

$\tau_{rz}=\dfrac{\left( \mathbb{P}_0-\mathbb{P}_L \right)r}{2L}$        Eq. (05b)

and 

$\tau_{R}=\tau_{rz}\vert_{r=R}=\dfrac{\left( \mathbb{P}_0-\mathbb{P}_L \right)R}{2L}$        Eq. (05c).

Recall that $\tau_{rz}$ is the shear stress and $\tau_{r}$ is the stress evaluated at the pipe wall. You should be aware that the pressure difference $\mathbb{P}_0-\mathbb{P}_L$ in Eqs. (05) includes the effect of gravity. The Reynolds number $N_{Re}$ is given by,

$N_{Re}=\dfrac{(4n)^{n}\,D^n\,V^{2-n}\rho}{g_c\,m\,(3n+1)^n8^{n-1}}$        Eq. (06)

where $g_c=32.174\,lb_m\,\cdot \,ft/lb_f\, \cdot s^2$ is a units correction factor used in the British units system. The density of the fluid $\rho$ must be given in $lb_m/ft^3$. Equation (06) was taken from the article of Dodge and Metzner [AIChE J 1959 5 (2)].

The friction factor $f_{FF}$, for laminar conditions $N_{Re}\leq N_{Re-c}$, is given by,

$f_{FF-L}=\dfrac{16}{N_{Re}}$        Eq. (07)

and for turbulent flow $4000< N_{Re}<10^5$ regime by,

$f_{FF-T}=\dfrac{0.0682\,n^{-1/2}}{N_{Re}^{1/(1.87+2.39\,n)}}$        Eq. (08)

and for the transition region $N_{Re-c}<N_{Re}\leq 4000$ by

$f_{FF-Tr}=1.79\times 10^{-4}\exp\left[ -5.24\,n \right]\,N_{Re}^{0.414+0.757\,n}$        Eq. (09)

Finally, the critical Reynolds number $N_{Re-c}$ is defined as,

$N_{Re-c}=2100+875(1-n)$        Eq. (10)

Equations (07-10) were taken from the paper of Darby et al. [Chem. Eng. 1992 99 (9)].

Plastic Bingham fluid

The flow rate $Q$ is given by,

$Q=\dfrac{\pi\,R^3\tau_w}{4\mu_\infty}\left[  1 - \dfrac{4}{3}\left( \dfrac{\tau_0}{\tau_w}\right)+ \dfrac{1}{3}\left( \dfrac{\tau_0}{\tau_w} \right)^4 \right]$        Eq. (11)

where $R$ is the pipe internal radius, $\mu_\infty$ is called the limiting viscosity and $\tau_0$ is the yield stress. Also, $\tau_w$

$\tau_w=\dfrac{\left(\mathbb{P}_0-\mathbb{P}_L\right)R}{2L}$        Eq. (12)

In Eq. (12) pressures $\mathbb{P}_0$ and $\mathbb{P}_L$ include the hydrostatic contribution in an inclined pipe. Formulas in Eqs. (11-12) were taken from the familiar book Dynamics of Polymeric Liquids by Bird R. B. et al. Subscripts $0$ and $L$ indicate the end and final of the pipe.

The Reynolds $N_{Re}$ and Hedstrom $N_{He}$ numbers are given by,

$N_{Re}=\dfrac{D\,V\, \rho}{\mu_\infty}$        Eq. (13)

$N_{He}=\dfrac{D^2\,\rho\,\tau_0 }{\mu_\infty^2}$        Eq. (14)

In this case the friction factor $f_{FF}$ is given for all flow regimes as,

$f_{FF}=\left( f_{FF-L}^m+f_{FF-T}^m \right)^{1/m}$        Eq. (15)

where,

$m=1.7+\dfrac{40000}{N_{Re}}$        Eq. (16)

and the friction factors for laminar $f_{FF-L}$ and turbulent $f_{FF-T}$ regimes are:

$f_{FF-L}=\dfrac{16}{N_{Re}}\left[ 1+\dfrac{1}{6}\dfrac{N_{He}}{N_{Re}}-\dfrac{1}{3}\dfrac{N_{He}^4}{f_{FF}^3N_{Re}^7} \right]$        Eq. (17)

$f_{FF-T}=\dfrac{10^a}{N_{Re}^{0.193}}$        Eq. (18)

$a=-1.47\left[ 1+0.146\exp\left( -2.9\times 10^{-5}N_{He} \right) \right]$        Eq. (19)

Notice that for plastic Bingham fluids there is no laminar-transition-turbulent regions reported, so that in order to find $f_F$ you must solve numerically Eq. (15). However, you may read the manuscript of Swamee and Aggarwal [J. Pet. Sci. Eng. 2011 76] if you would like to know about an effort to give a critical $N_{Re}$ for these fluids. Equations (13-19) were taken from the paper of Darby et al. [Chem. Eng. 1992 99 (9)].

Watch this video if you do not want to read. Enjoy!



Sunday, September 17, 2023

Como calcular la densidad de una solución

 En el caso de una solución acuosa de ácido acético al 9% en peso a una temperatura de 17 °C.

Procedimiento de cálculo

Primero que nada, nótese que por cada 100 gr de solución se tienen 9 gr de C$_2$H$_4$O$_2$. Por lo tanto, debe haber también 91 gr de H$_2$O. Luego, por separado buscamos las densidades del ácido acético y del agua a 17 °C,

Densidad C$_2$H$_4$O$_2$ = 1.05 gr/cm$^3$
Densidad H$_2$O = 0.9987 gr/cm$^3$

Calculamos ahora el volumen de C$_2$H$_4$O$_2$ y de H$_2$O

Volumen C$_2$H$_4$O$_2$ 

$= \dfrac{9 \text{ gr}}{(1.05 \text{ gr/cm}^3)} = 8.58 \text{ cm}^3$ de C$_2$H$_4$O$_2$

Volumen H$_2$O 

$= \dfrac{91 \text{ gr}}{0.9987 \text{ gr/cm}^3} = 91.1118 \text{ cm}^3$ de H$_2$O

La masa total de la solución son 100 gr y el volumen total de la solución es:

 $\left( 8.58+91.1118 \right)$ cm$^3$ = 99.6918 cm$^3$ 

Por la tanto, la densidad de la solución $\rho_{sol}$ es

$\rho_{sol}= \dfrac{100 \text{ gr}}{99.69118 \text{ cm}^3}$
= 1.00309 gr/cm$^3$
= 1003.09 kg/m$^3$

Most popular posts